收藏本站
NCP374
PIN FUNCTION DESCRIPTION
Pin
Pin
1, 2
3
4
5
6
7
8
9
10
11
Name
VBUS
GND
RES1
RES2
RES3
Ilim
EN
DIR
FLAG
IN
Type
POWER
POWER
INPUT
INPUT
INPUT
OUTPUT
INPUT
INPUT
OUTPUT
POWER
Description
VBUS voltage pins: must be hardwired together on the PCB.
These pins are connected to the VBUS connector, and are protected against positive and negative
overvoltage events.
A 1 m F low ESR ceramic capacitor, or larger, must be connected between these pins and GND.
Ground
Reserved pin. Must be connected to GND potential and used for IC test.
Reserved pin. Must be connected to GND potential and used for IC test.
Reserved pin. Must be connected to GND potential and used for IC test.
Current Limit Pin. This pin provides the reference, based on the internal band ? gap voltage reference,
to limit the over current, across internal NMosFet. A 0.1% tolerance resistor shall be used to get the
highest accuracy of the Over Current Limit.
Enable Pin. In combination with DIR, the internal NMOSes are turned on if Battery is applied on the
IN pins. (See logic table)
In enable mode, the internal Over ? Current protection is activated from IN to VBUS. When enable
mode is disabled, the NCP374 current consumption, into IN pin, is drastically decreased to limit cur-
rent leakage of the self powered devices.
Direct Mode pin. This pin can be used, in combination with Enable pin, for the front end protection
applications like wireless devices. In this case, the part can be used as +/ ? OVP only. See logic
table.
Fault indication pin.
This pin allows an external system to detect fault condition.
The FLAG pin goes low when input voltage exceeds OVLO threshold or drops below UVLO
threshold (charging mode), charge current from IN to VBus exceeds current limit or internal temper-
ature exceeds thermal shutdown limit.
Since the FLAG pin is open drain functionality, an external pull up resistor to VBat must be added
(10 k W minimum value).
IN pin. In Front end application this pin is connected to charger device input or PMIC input.
In host application, this pin is connected to upstream DCDC. This pin is used as power supply of the
core and current from IN to VBUS is then limited to the external
12
13
NC
PAD1
NA
POWER
Not internally connected. Can be connected to any potential.
Drain connection of the back to back MOSFET’s. This exposed pad mustn’t be connected to any
other potential and must be used for thermal dissipation of the internal MOSFETs.
http://onsemi.com
4
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NCP5104BA36WGEVB EVAL BOARD FOR NCP5104BA36WG
NCP5181BAL36WEVB BOARD EVAL NCP5181 36 W BALLAST
NCV73810V2GEVB BOARD EVAL FLEXRAY BUS NCV7381
NF20AA0509MHL CURRENT LIMITER INRUSH 5OHM 20%
NHD-4.3-480272MF-20 BOARD CTRLR FOR NHDEV 4.3 TFT
NHDEV DEVELOPMENT BOARD BOARD DEV LCD COG TFT 100X95MM
NP0120TAT1G IC PROTECTOR LOW CAP 12V 5TSOP
NP1500SCT3G THYRISTOR TSPD 100A 150V SMB
相关代理商/技术参数
NCP380HMU05AATBG 功能描述:电源开关 IC - 配电 OVER CURRENT PROTECTION RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5
NCP380HMU05AGEVB 功能描述:电源管理IC开发工具 NCP380 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
NCP380HMU10AATBG 功能描述:电源开关 IC - 配电 OVER CURRENT PROTECTION RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5
NCP380HMU10AGEVB 功能描述:电源管理IC开发工具 NCP380 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
NCP380HMU15AATBG 功能描述:电源开关 IC - 配电 OVER CURRENT PROTECTION RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5
NCP380HMU15AGEVB 功能描述:电源管理IC开发工具 NCP380 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
NCP380HMU20AATBG 功能描述:电源开关 IC - 配电 OVER CURRENT PROTECTION RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5
NCP380HMU20AGEVB 功能描述:电源管理IC开发工具 EVALN BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V